Home > Error Code > Aix Error Code 569

Aix Error Code 569

Contents

Token-Ring network adapter is being identified or configured 851T1/J1 Portmaster adapter is being identified or configured 852Progress indicator. A POWER RADian device driver is being configured 857Progress indicator. Refer to the following RSPC location code examples: Processor-PCI bus 00-00 PCI bus Memory module in system planar 00-00-00-01 Memory module in card 00-0A-00-01 Integrated PCI adapters 04-A0 ISA bus (Integrated A POWER GXT110P graphics adapter is being configured 901Progress indicator. his comment is here

A multi-bus integrated Ethernet adapter is being configured 791Progress indicator. c43 Cannot access the boot/install tape. A graphics visualization server adapter is being configured 983Progress indicator. IPL control block is being initialized 221NVRAM CRC miscompare occurred while loading the operating system with the key mode switch in Normal position.

0552 Aix Error Code

Solve problems - It's Free Create your account in seconds E-mail address is taken If this is your account,sign in here Email address Username Between 5 and 30 characters. Partial dump completed. c29 The system was unable to configure the network device.

Asynchronous expansion drawer is being identified or configured 935Progress indicator. 3.5-inch diskette drive is being identified or configured 936Progress indicator. 5.25-inch diskette drive is being identified or configured 937An HIPPI adapter I am using rpower to re-boot the failover with the reservations still set on the primary. Querying card in slot 8 510Progress indicator. Aix Led Codes c52 Changing from RAM environment to disk environment.

A 2.2 GB 16-bit SCSI disk drive is being identified or configured 705Progress indicator. Aix Error Codes List A 13 GB 1/4 inch tape drive is being configured 758Progress indicator. NVRAM is being identified or configured 815Progress indicator. Attempting a Normal-mode system restart from Token-Ring specified in the NVRAM boot devices list 228Progress indicator.

A WDC AC31000H 2083 IDE disk drive is being identifed or configured 990Progress indicator. 2.0GB SCSI disk drive is being identified or configured 991525MB 1/4-inch cartridge tape drive is being identified Aix Reference Codes Built-in self-test started array-initialization program test code 152Progress indicator. In most cases, the prefix value assignments were chosen to provide some mnemonic characteristic, so that they would be easier to remember. is your dump device on an FC attached disk?

Aix Error Codes List

It identifies a device that is part of the parent, a connector, or a cable. Built-in self-test started cyclic redundancy-check character (CRC) check on the 8752 EPROM 121Built-in self-test detected a bad CRC on the on-chip sequencer EPROM 122Progress indicator. 0552 Aix Error Code A 2.2 GB Fast/Wide SCSI SE disk drive is being configured 756Progress indicator. 0554 Error Code In Aix This code is only used when there is no console.

A Single Mode 8MB PCI ATM Adapter is being identified or configured 697Progress indicator. http://bsnux.com/error-code/aix-517-error-code.html Two-button mouse is being identified or configured 925Progress indicator. An RS/6000 SCSI I/O control initiator is being configured 977Progress indicator. All rights reserved. 0518 Error Code Aix

c48 Prompting you for input. or is thet where it tries to copy the dump when it reboots? Adapter card slots are being queried 289Progress indicator. weblink Waiting for Interactive Maintenance Analysis Procedures (IMAP) request.

A 1 GB 16 bit SE SCSI disk drive is being configured 780Progress indicator. Ibm Code D133c002 Standard speaker is being identified or configured 929Progress indicator. Attempting a Service-mode system restart from the 9333 High-Performance Disk Drive Subsystem devices specified in the NVRAM boot device list 245Progress indicator.

Integrated Ultra2 SCSI Controller being identified or configured 663Progress indicator.

Attempting a Service-mode system restart from the standard I/O planar-attached devices specified in the NVRAM boot device list 243Progress indicator. Vendor display adapter is being identified or configured 893Progress indicator. An L2 cache is being identified or configured 710Progress indicator. A display device driver is being identified or configured 700 - 7C6 AnzeigeBeschreibung 77CProgress indicator.

c42 Extracting data files from diskette. Physical location codes provide a mapping of logical functions in a platform (or expansion sites for logical functions, such as connectors or ports) to their specific locations within the physical structure Menus are being displayed on the local display or terminal connected to your system 261The system waits for a response from an asynchronous terminal on serial port 1 262The system waits http://bsnux.com/error-code/aeg-c2-error-code.html Forum Operations by The UNIX and Linux Forums Log In E-mail or User ID Password Keep me signed in Recover Password Create an Account Blogs Discussions CHOOSE A TOPIC Business

c53 Not enough space in the /tmp directory to do a preservation installation. I/O planar test started 291Progress indicator. The system halts 209Reserved. The system halts 180Progress indicator.

The system halts 151Progress indicator. The system halts 165The built-in self-test encountered an error while writing low NVRAM. For example: For async devices, GH defines the port on the fanout box. A WDC AC2700H 730 MB IDE disk is being configured 960Progress indicator.

If you are working with a RSPC model use the Location Codes for RSPC Model Architecture System Units. The crash codes that follow are part of a Type 102 message. P2 identifies an I/O planar (including all integrated I/O devices). The first group tracks the progress of the configuration program.