Home > Error Code > Aix 517 Error Code

Aix 517 Error Code

Contents

Zenoss Service Dynamics Architecture Overview MoreWhitePapers Best Answer 0 Mark this reply as the best answer?(Choose carefully, this can't be changed) Yes | No Saving... If any device are in missed state, (in Cudv chgstatus=3) display it. The next screen displays a warning that indicates you will not be able to return to the Base OS menu without rebooting. finally the synchronization of the ODM in the BLV with the ODM from the / (root) filesyatem is done by the savebase command. navigate here

c33 = console is a TTY. A 4.5GB 16-bit SE SCSI disk drive is being identified or configured. 707 Progress indicator. It is still possible, in the end, that isolation of the problem may indicate a restore or reinstall of AIX is necessary to correct it. Display the processes: # ps -ef | grep find root 28972 13964 0 11:07:33 pts/0 0:00 grep find # To delete this record from the /etc/inittab file, you use the rmitab http://www-01.ibm.com/support/docview.wss?uid=isg3T1000131

Aix Led 517

cron 10.pb cleanup (piobe) 11.getty for the console (cons) The System Resource Controller (SRC) has to be started near the begining of the etc/inittab file since the SRC daemon is needed The diagnostic program will then load and run the diagnostics automatically. c70 Problem Mounting diagnostics CDROM disc. If this is a VIOS LPAR, use the correct VIOS media.

c34 A file was selected. Regards Top Best Answer 0 Mark this reply as the best answer?(Choose carefully, this can't be changed) Yes | No Saving... Any helpful pointers describing what I should be investigating next would help. Aix Maintenance Mode Commands Software ROS (also named bootstrap) forms an IPL control block which is compatible with AIX 5L Version 5.3, takes control and builds AIX 5L specific boot information.

A partial dump was written to the dump device. activate primary paging space. rc.boot 2 in detail rc.boot 2 (LED 551) ipl_varyon to activate rootvg ( success LED= 517, error LED=552,554,556). https://groups.google.com/d/topic/comp.unix.aix/2Q1_MDASvTY NOTE: The -y option gives fsck permission to repair file system corruption when necessary.

Restart the process when it dies. Aix Fsck Command Init with rc.boot 1 configures base devices. Good luck. In this class, devices with the attribute phase=1 are considered base devices.

0554 Error Code In Aix

Close this window and log in. http://unix.ittoolbox.com/groups/technical-functional/ibm-aix-l/aix-0517-error-code-3510794 and moreover if i do preservation installation can i save my other file system except /usr, /tmp, /var, and / (root) file systems ?? Aix Led 517 c32 = console is an LFT terminal. 0552 Aix Error Code The /etc/inittab file is composed of entries that are position-dependent and have the following format, /etc/inittab format = Identifier:RunLevel:Action:Command Each entry is delimited by a newline character.

You can also refer to the document titled "Booting in Service Mode," available at http://techsupport.services.ibm.com/server/aix.src hBroker. 2. http://bsnux.com/error-code/aht-error-code.html the copycore command checks if a dump occured. This signals the user that a Flash Update may be initiated by moving the key switch to the SERVICE position. Unknown User replied Sep 18, 2003 Do you have any recent backups, like a mksysb and rootvg backups? 0518 Error Code Aix

Unknown User replied Dec 3, 2003 Hi, I hope you have solved your problem, but 517 and 518 LED codes refer to network boot and mounting remote file systems. Eg: if the system is in run level 1, only those entries with a 1 in the run-level field are started. -When you request the init command to change run levels, To temporarily replace the disk-based /etc/filesystems file, run the following commands: mount /dev/hd4 /mnt mv /mnt/etc/filesystems /mnt/etc/filesystems.[MMDDYY] cp /etc/filesystems /mnt/etc/filesystems umount /mnt MMDDYY represents the current two-digit representation of the Month, his comment is here Enter: fsck /dev/[LVname] LVname is the name of your user-defined logical volume.

Correct the problem causing the error. Aix Led Codes boot Process the entry only during system boot, which is when the init command reads the /etc/inittab file during system startup. I've had to do this in the past.

You requested a dump using the SYSDUMPSTART command, a dump key sequence, or the Reset button. 0c3 The dump is inhibit 0c4 The dump did not complete.

There are no limits (other than maximum entry size) on the number of entries in the /etc/inittab file. Isolating the cause of the hang could be excessively time-consuming and may not be cost-effective in your operating environment. No spaces please The Profile Name is already in use Password Notify me of new activity in this group: Real Time Daily Never Keep me informed of the latest: White Papers Aix Fsck Mounted Filesystem and for boot from CD, don't forget that you have to choice maintenance mode with minimum shell , and then you can do bosboot.

Toolbox.com is not affiliated with or endorsed by any company listed at this site. Cancel Red Flag SubmittedThank you for helping keep Tek-Tips Forums free from inappropriate posts.The Tek-Tips staff will check this out and take appropriate action. If you used the preceding procedure to temporarily replace the /etc/filesystems file, and you have user-created file systems in the rootvg volume group, you must also run the following command: imfs http://bsnux.com/error-code/aeg-c2-error-code.html Has anyone else experienced similar problem?

The /etc/inittab file supplies the script to the init command's role as a general process dispatcher. so here is the step for jfslog: Or you can google on "IBM AIX LED 517"Boot into service mode from the installation cds or NIM. #fsck -y /dev/hd2 #fsck -y /dev/hd3 irrecoverable error. 536 The configuration manager encountered more than one sequence rule specified in the same phase. (irrecoverable error). 537 The configuration manager encountered an error when invoking the program in e.

To isolate the possible cause of the hang, would require a debug boot of the system. Software ROS then locates, loads, and turns control over to AIX 5L Boot Logical Volume (BLV). This flag can be used to avoid having to manually answer multiple confirmation prompts, however, use of this flag can cause permanent, unnecessary data loss in some situations. Make the secondary dump device ready, then press CTRL-ALT-NUMPAD2. 0c7 Reserved. 0c8 The dump function is disabled.

Regards Join this group Popular White Paper On This Topic The Difference Between Microsoft Azure & Amazon AWS 10Replies Best Answer 0 Mark this reply as the best answer?(Choose carefully, this