Home > Aix Error > Aix Error Code E105

Aix Error Code E105

It hung with the preceding errors and then with LED 40b and E075. To correct this situation, perform the following: Boot system in service mode. Action: Refer to the SSA Adapters: User's Guide and Maintenance Information. 40064 Description: A 64MB DRAM module in adapter card slot 0 has failed. Action: Refer to the SSA Adapters: User's Guide and Maintenance Information. 49000 Description: A RAID array is in the Degraded state because a disk drive is not available to the array, his comment is here

If there are at least two PVs in the VG rootvg, if one fails to work with this command, try any of the remaining PVs (eg, /etc/continue hdisk0 or /etc/continue hdisk1) Various steps, such as those listed in the "Solution summary" section of this document, should be taken first to rule out the more likely causes of this error. Action: Refer to the SSA Adapters: User's Guide and Maintenance Information. 48000 Description: The SSA adapter has detected a link configuration that is not valid. E176 TFTP file transfer E177 Transfer failure due to TFTP error condition E178 Create PCI token ring node E180 Service Processor Command setup E181 Send drawer data to I/O planar E182

Action: Refer to the user's or service guide for the unit containing the disk drive. Action: Refer to the SSA Adapters: User's Guide and Maintenance Information. 42200 Description: Other adapters on the SSA loop are using levels of microcode that are not compatible. If this doesn't appear to be working, type the following at the command line:     sync; sync; halt 13) If the problem still persists, consult your local SE before you attempt After the keyboard name or icon appears, the user can enter the Systems Management Services menu by hitting the "1" key (if ASCII terminal) or the "F1" key (if Graphics terminal).

If necessary, contact your AIX support center for assistance with these steps. shutdown -Fr top of page 581 TCP/IP problem: This LED is displayed when the /etc/rc.net script is executed. Action: Refer to the SSA Adapters: User's Guide and Maintenance Information. 41016 Description: A 16MB DRAM module in adapter card slot 1 has failed. Depending on the node, this procedure may work or may result in the same errors.

A Format operation has been ended before it has completed. Solution The LED code E105 generally indicates a network problem. Boot Image Execution * Once a boot image is located on a device in the Boot List, the system firmware code hands off control to the AIX Boot code. * LCD Action: Refer to the user's or service guide for the unit containing the disk drive.

Verify the duplex setting on your nodes with the lsattr command. To attempt to isolate the problem, the en0 adapter was unplugged from node 49 and 53 and terminated using two different terminators. Control is later handed over to AIX under the E105 LCD code, after which AIX codes are seen, which all begin with 0xxx. Action: Refer to the SSA Adapters: User's Guide and Maintenance Information. 42521 Description: An SSA fast-write cache failure has been detected.

Action: Refer to the SSA Adapters: User's Guide and Maintenance Information. 42524 Description: An SSA write-cache resource is not available. http://marc.info/?l=aix-l&m=97001051609835&w=2 Some space needs to be free on these logical volumes for the system to boot properly. To correct this situtation, perform the following steps: Boot system in service mode. COM> Date: 2000-09-26 23:17:16 [Download message RAW] hello christian, if you go there it means "normal boot" http://www.rs6000.ibm.com/resource/hardware_docs/syss6/a4ak3b05.html Header_28Typical Boot Sequence for RS/6000 7025 F50 Series After the A/C power

An SSA device cannot be configured. this content The last two digits in the checkpoint can be used to help isolate the location of the I/O activity that caused the problem. "x" indicates the I/O drawer number. "y" indicates Make sure the card is seated properly and all internal and external SCSI connectors are firmly attached. Action: Refer to the user's or service guide for the unit containing the disk drive. 2FFFF Description: An async code that is not valid has been received.

E07A Waiting for keystroke from local console E07B Waiting for keystroke from remote console E07F Service Processor exiting from session with local or remote terminal. An attempt was made to network boot the system for install or into Maintenance mode but was not successful. Processor ----------------------------------------------------------------------------- 91001100 Remote IPL error, insufficient memory Defective/insufficient mem. 91001200 Remote IPL error - incorrect IP format for client IP address 91001300 Remote IPL error - incorrect IP format for weblink Action: Refer to the SSA Adapters: User's Guide and Maintenance Information. 47000 Description: An attempt has been made to store in the SSA adapter the details of more than 32 RAID

The disk drive might be going to fail. Action: Refer to the SSA Adapters: User's Guide and Maintenance Information. 42527 Description: A dormant SSA fast-write cache entry exists. Action: Refer to the SSA Adapters: User's Guide and Maintenance Information. 50200 Description: Duplicate SSA cluster number detected.

Proc., Sys.

If after other, potential causes of this problem have been ruled out, such as those listed in the "Solution summary" section of this document, and you suspect the adapter setting is Built-In-Self-Test (BIST) * The Service Processor initiates Built-In-Self-Test (BIST) on the Central Electronics Complex (CEC) chips when the POWER Button is pressed. * The VPD data is read and the CRC Please try the request again. Either boot the system from boot diskettes or boot tape Select option to perform system maintenance functions from the INSTALL and MAINTENANCE menu.

Action: Refer to the SSA Adapters: User's Guide and Maintenance Information. 41008 Description: An 8MB DRAM module in adapter card slot 1 has failed. Wrong password entered 20E00002 Privileged-access password jumper is in wrong jumper position 20E00003 Power on password must be set for Unattended Mode 20E00004 Battery needs drained or replaced Battery, System Board Open a TTY session to the node. check over here Please try the request again.

Memory modules 2. Action: Refer to the SSA Adapters: User's Guide and Maintenance Information. 42528 Description: A fast-write SSA disk drive has been detected that was previously unsynchronized, but has since been configured on D0300 Description: The disk drive module failed the diagnostic test. An attempt was made to boot node 29 into Maintenance mode using AIX Version 4.3.2 SPOT.

Proc., System Board 2BA00019 IRQ13 test failure System Board, Serv. Action: Refer to the SSA Adapters: User's Guide and Maintenance Information. 48600 Description: Member disk drives of an SSA array are not all on the same SSA loop, in a multiple-host-system E129 Validate target RAM address E12A copy to RAM, flush cache E12B Set MP operational parameters E12C Set MP cpu node characteristics E12D Park secondary processors in parking lot E12E Primary If not, goto the next step, else consult your local SE for further advice.